Poly-Fine II Series Filter Cartridges product photo Primary L

Poly-Fine II Series Filter Cartridges

  • Proprietary filter media produced by Pall for highly consistent performance
  • High contaminant-holding capacity
  • Wide chemical compatibility
  • Rigid polypropylene outer cage protects filter
  • All polypropylene one piece construction (except 0.2 micron)
  • Asymmetric polysulfone media used in 0.2 μm grade
  • Fast rinse-up to 18 Megohm-cm
  • Application- Specification-

    Performance Specifications

    Filter Grades:

    0.2, 0.25, 0.45, 0.8, 2, 3, 5, 10, 30, 50, 100 μm

    Recommended change-out differential pressure1

    2.4 bard (35 psid)

    Maximum forward differential pressure

    4.8 bard (70 psid) @ 20°C (68°F)
    2.8 bard (40 psid) @ 65°C (150°F)

    Food and water contact use

    Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.

    Cartridge rinse-up

    Rinse-up to 18 Megohm-cm with a minimum of throughput.

    Purity

    Cartridges are free of resins, binders, and adhesives.

    Sterilization:

    Multiple autoclaving for 30 minutes at 121°C (250°F) under no end load conditions. In -line steam sterilization is not recommended. May be in-line sanitized with hot water at 82°C (180°F) for 1 hour.

    Product Specifications

    Materials of construction

     
    Filter Media:  
        PFT 0.2: Highly asymmetric polysulfone
        All other grades: Polypropylene
    Hardware: Polypropylene
    Sealing: Thermal bond
    Support material: Polypropylene
    Gaskets/O-rings: Silicone elastomer, nitrile, EPDM
    fluorocarbon elastomer, white nitrile,
    white silicone, expanded PTFE, FEP
    encapsulated silicone, high purity
    fluorocarbon elastomer, FEP
    encapsulated fluorocarbon elastomer,
    Kalrez2, white neoprene
     


    Dimensions (nominal):

     
    Outside Diameter: 6.6 cm (2.6 in)
    Lengths: 10.2 cm (4 in), 24.8 cm (9.75 in),
    25.4 cm (10 in), 49.5 cm (19.5 in),
    50.8 cm (20 in), 74.3 cm (29.25 in),
    76.2 cm (30 in), 99.1 cm (39 in),
    102 cm (40 in)
     

    1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
    2 Registered trademark of DuPont Dow.


    Download Datasheet
    Description
  • Proprietary filter media produced by Pall for highly consistent performance
  • High contaminant-holding capacity
  • Wide chemical compatibility
  • Rigid polypropylene outer cage protects filter
  • All polypropylene one piece construction (except 0.2 micron)
  • Asymmetric polysulfone media used in 0.2 μm grade
  • Fast rinse-up to 18 Megohm-cm
  • Application- Specification-

    Performance Specifications

    Filter Grades:

    0.2, 0.25, 0.45, 0.8, 2, 3, 5, 10, 30, 50, 100 μm

    Recommended change-out differential pressure1

    2.4 bard (35 psid)

    Maximum forward differential pressure

    4.8 bard (70 psid) @ 20°C (68°F)
    2.8 bard (40 psid) @ 65°C (150°F)

    Food and water contact use

    Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.

    Cartridge rinse-up

    Rinse-up to 18 Megohm-cm with a minimum of throughput.

    Purity

    Cartridges are free of resins, binders, and adhesives.

    Sterilization:

    Multiple autoclaving for 30 minutes at 121°C (250°F) under no end load conditions. In -line steam sterilization is not recommended. May be in-line sanitized with hot water at 82°C (180°F) for 1 hour.

    Product Specifications

    Materials of construction

     
    Filter Media:  
        PFT 0.2: Highly asymmetric polysulfone
        All other grades: Polypropylene
    Hardware: Polypropylene
    Sealing: Thermal bond
    Support material: Polypropylene
    Gaskets/O-rings: Silicone elastomer, nitrile, EPDM
    fluorocarbon elastomer, white nitrile,
    white silicone, expanded PTFE, FEP
    encapsulated silicone, high purity
    fluorocarbon elastomer, FEP
    encapsulated fluorocarbon elastomer,
    Kalrez2, white neoprene
     


    Dimensions (nominal):

     
    Outside Diameter: 6.6 cm (2.6 in)
    Lengths: 10.2 cm (4 in), 24.8 cm (9.75 in),
    25.4 cm (10 in), 49.5 cm (19.5 in),
    50.8 cm (20 in), 74.3 cm (29.25 in),
    76.2 cm (30 in), 99.1 cm (39 in),
    102 cm (40 in)
     

    1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
    2 Registered trademark of DuPont Dow.
    Specifications

    Performance Specifications

    Filter Grades:

    0.2, 0.25, 0.45, 0.8, 2, 3, 5, 10, 30, 50, 100 μm

    Recommended change-out differential pressure1

    2.4 bard (35 psid)

    Maximum forward differential pressure

    4.8 bard (70 psid) @ 20°C (68°F)
    2.8 bard (40 psid) @ 65°C (150°F)

    Food and water contact use

    Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.

    Cartridge rinse-up

    Rinse-up to 18 Megohm-cm with a minimum of throughput.

    Purity

    Cartridges are free of resins, binders, and adhesives.

    Sterilization:

    Multiple autoclaving for 30 minutes at 121°C (250°F) under no end load conditions. In -line steam sterilization is not recommended. May be in-line sanitized with hot water at 82°C (180°F) for 1 hour.

    Product Specifications

    Materials of construction

     
    Filter Media:  
        PFT 0.2: Highly asymmetric polysulfone
        All other grades: Polypropylene
    Hardware: Polypropylene
    Sealing: Thermal bond
    Support material: Polypropylene
    Gaskets/O-rings: Silicone elastomer, nitrile, EPDM
    fluorocarbon elastomer, white nitrile,
    white silicone, expanded PTFE, FEP
    encapsulated silicone, high purity
    fluorocarbon elastomer, FEP
    encapsulated fluorocarbon elastomer,
    Kalrez2, white neoprene
     


    Dimensions (nominal):

     
    Outside Diameter: 6.6 cm (2.6 in)
    Lengths: 10.2 cm (4 in), 24.8 cm (9.75 in),
    25.4 cm (10 in), 49.5 cm (19.5 in),
    50.8 cm (20 in), 74.3 cm (29.25 in),
    76.2 cm (30 in), 99.1 cm (39 in),
    102 cm (40 in)
     

    1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
    2 Registered trademark of DuPont Dow.
    Performance

    Particle Retention (µm)

     
    Cartridge
    Designation
    Liquid Service
    (by ASTM F-795 Test)
    Gas Service
    90%
    Efficiency
    >99.9%
    Efficiency
    Removal Efficiency
    By DOP Test
    PFT 0.2 0.2 0.5 99.99%
    PFT 0.25 0.25 1.0 99.97%
    PFT 0.45 0.45 1.2 99.93%
    PFT 0.8 0.8 2.5 99.90%
    PFT 2.0 2 5 -
    PFT 3.0 3 7 -
    PFT 5.0 5 12 -
    PFT 10.0 10 15 -
    PFT 30.0 30 40 -
    PFT 50.0 50 65 -
    PFT 100.0 85 100 -
     


    Typical Flow vs. Differential Pressure for Application Sizing

    Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).



    Unit conversion: 1 bar = 100 kPa

    Ordering Information

    Pall Part Number = PFT [1] - [2]U[3] - [4][5][6] - [7]



    Table 1

     
    Code Filter grades (μm)
    0.2 0.2
    0.25 0.25
    0.45 0.45
    0.8 0.8
    2 2
    3 3
    5 5
    10 10
    30 30
    50 50
    100 100
     


    Table 2

     
    Code Cartridge lengths (cm/ in) nominal
    4 10.2/4
    9.75 24.8/9.75
    10 25.4/10
    19.5 49.5/19.5
    20 50.8/20
    29.25 74.3/29.25
    30 76.2/30
    39 99.1/39
    40 101.6/40
     


    Table 3

     
    Code Gasket/O-ring materials
    S Silicone
    (standard O-rings)
    N Nitrile
    (standard gaskets)
    M White silicone
    W White nitrile (gaskets)
    V Fluorocarbon
    elastomer
    E EPDM
    T FEP encapsulated
    silicone (O-rings)
    T Expanded PTFE
    (gaskets)
    X No O-ring required
    (M2 style only)
    F FEP encapsulated
    fluorocarbon
    elastomer (O-rings)
    K Kalrez (222 O-rings)
    Q High purity
    fluorocarbon
    elastomer
    (222 O-rings)
    Z White neoprene
    (gaskets)
     


    Table 4

     
    Code End configurationss
    Blank DOE industrial
    1X DOE industrial, 2.54 cm (1 in) extended core
    M2 SOE flat closed end, fits housings with 020 O-ring post
    M3 SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0)3
    M3H SOE large diameter closed end, external 222 O-rings
    M4 SOE fin end, external 222 O-rings with locking tabs
    M5 DOE, internal 120 O-rings (retrofits 213 O-ring style) 3
    V Fluorocarbon
    elastomer
    M6 SOE flat closed end, external 226 O-rings (retrofits other manufacturers’ Code 6)3
    M7 SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7)3
    M8 SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5)3
    M10 DOE, internal O-rings (fits other manufacturers’ housings)3
    M11 SOE flat closed end, internal 120 O-ring (retrofits other manufacturers’ X style) 3
    M18 SOE flat closed end, external 222 O-ring
    M20 SOE, internal O-ring (same as M10), closed end with deep recess
    M22 SOE fin end, external 225 O-ring
     


    Table 5

     
    Code Bubble test option
    Blank No bubble test
    B 100% bubble best
     


    Table 6

     
    Code Pre-rinse option
    Blank No pre-rinse
    414 100% pre-rinse
     


    Table 7

     
    Code Packaging
    Blank Standard packaging
    -BLK Bulk packaging
     


    3 For details, contact Pall Corporation.
    Segment
    Cartridge Filters